Free Shipping Worldwide

Please measure your car logo before placing order !

5D/4D Volkswagen light up badge logo

Product Features:

1. The appearance of this product is consistent with the original car logo. It is installed in the position of the boot logo and can directly replace the original car logo. The special vacuum electroplating technology is adopted to ensure that the glossiness is consistent with the original car label and that the high transmittance and brightness are uniform.
2. Adopt high quality LED light group, with high brightness, long service life, etc, special design waterproof, dustproof, ensure a long time of use.
3. This product is specially designed for car modification lovers. When the light does not turn on during the daytime, it is no different from the original car logo. When the light is turned on at night, then the LED logo lights up, making the logo become a dazzling, highly futuristic sense of technology, highlighting your beloved car's noble lineage.
4. The inside LED lamp adopts a special waterproof and dustproof design! LED lights have a lifecycle up to 100,000 hours.
5. Adopt high quality double-sided adhesive tape for automobile, the adhesive force is very strong and durable!

Specification：

• Colour: Red, white and blue
• Power: DC12V+/-10%
• Wiring Length: 0.6m
• Power: 2 W
• Voltage: 12 V
• Current: 0.1 A

Tools prepared before installation
Have the following tools ready before you start:

1. Flat head screwdriver
2. Phillips screwdriver
3. Insulating tape
4. Towel
5. Pliers

Installation Instructions

• First, lay a towel beside the trunk logo and use a flat screwdriver to pry the logo. Lay a towel to prevent scratching the body.
• Take care to peel the double-sided adhesive tape off the body of the car first, and use moderate force when prying, but don't be too hard. Bit by bit, the double-sided adhesive tape will come off slowly, then clean the badge and the body of the car.
• Remove the bulkhead inside the trunk with a screwdriver. Be Noted that there are clamps in some places.
• Now let's install the car label lights. The power cord of the lamp goes through one of the locating holes and goes into the trunk to tear off the single glue on the back of the lamp. While pulling the wire, glue the beacon light onto the car body and press it down.
• The beacon light has been installed, and the power is now connected. The lights should be connected to the rear license plate power source. When the night light is turned on, the beacon light will also be turned on at the same time. Find the power connector of the rear license plate light.
• First unplug the plug, the positive and negative pole each strip a hole, expose the wire core, press red to red, black to black to connect the line. Don't forget to wrap it in the insulating tape and finally put the plug back in!
• Reinstall the sound insulation panel of the trunk cover.

Shipping 

• We will check the product in good condition before shipment. Free shipping on all of car emblems through international economic express. 
• Because of the epidemic situation, the shipping time is not under our control, perhaps longer than usual.
• Please make sure the size of logo you purchased works for your car.

 Applicable models

• Car front size: about 11CM suitable for (Golf/Magotan/CC/Tiguan/Bora/Scirocco etc.)

• Car front size: about 11CM suitable for (15-19 Lavida/Golf7/12-15 Santana/15-20 Sagitar/19-20 Lamando/ Touran L/18-19 T-Roc/16-20 Bora/ 19-20 CC/13-16 Jetta/17-18 Magotan/16-20 Passas

Credit card payment method

1. If you want to checkout with Credit Card. Please click PayPal and look for ‘Pay with Debit or Credit Card.

2. You don't need paypal account and pay through guest account. 

3. Enter your Payment details, your Billing Address, and your Contact Information.